Free-Spin Kit 2005-2014 Ford F-250 and F-350 with Warn Hubs for SRW and DRW

The Dynatrac Free-Spin hub conversion kit, SKU DT FO60-3X1104-C, replaces the factory unit bearings on 2005-2014 Ford F-250 and F-350 Super Duty 4x4 trucks with a fixed-spindle setup. It combines heat-treated chromoly spindles, serviceable Timken bearings and seals, and 35-spline, 1.50-inch outer axle shafts with Warn Premium locking hubs. Installation is bolt-on, with no machining or welding, and Dynatrac states the kits are made in the USA.

Why convert away from unit bearings

A factory unit bearing is a sealed assembly. Dynatrac describes it as non-serviceable, impossible to inspect, and prone to failure, so when it goes bad the entire unit is replaced. The Free-Spin conversion changes the front end to a conventional spindle with separate inner and outer tapered roller bearings, races, and a hub seal, so you can pull the hub, inspect the bearings, repack them, and replace only what is worn. Dynatrac lists a smoother ride, better fuel economy, and longer axle life as benefits of the design. Those are manufacturer claims, and results depend on the truck, tires, and driving.

What is in the kit

• Heat-treated chromoly spindles
• Cast nodular wheel hubs (8-on-170mm)
• Serviceable Timken bearings, races, and seals
• 35-spline, 1.50-inch outer axle shafts
• Warn Premium manual locking hubs
• Wheel studs and mounting hardware
• ABS tone rings and sensor mount

Warn locking hubs

This kit uses Warn Premium manual locking hubs, the standard hub in Dynatrac's Free-Spin line. They are 35-spline to match the outer shafts and are turned by hand: set them to lock before you engage four-wheel drive, and set them to free for street driving so the wheels turn without dragging the outer axle shafts along. Warn is the lower-priced of the two hub options Dynatrac offers. If you would rather have the shorter DynaLoc hub, the DynaLoc version of this kit is a separate listing in our catalog.

Fitment for 2005-2014 Ford Super Duty

This kit fits 2005-2014 F-250 and F-350 Super Duty 4x4 trucks, both single rear wheel (SRW) and dual rear wheel (DRW). Dynatrac states that its Free-Spin kits for 2005-2014 F-450 and F-550 trucks and for Ford dually trucks from 2005 on reuse the factory wheel adapters, so dually owners do not need an aftermarket adapter. The front axle is the Dana 60. The hubs are 8-on-170mm and reuse your existing rotor, and the kit carries ABS tone rings and a sensor mount so the factory ABS setup stays in place.

Service parts are easy to find

Dynatrac says every Free-Spin kit uses K30 bearings and seals, so replacements come from ordinary bearing suppliers. The common wear items are the Timken 387A inner bearing with 382A race, the Timken LM104949 outer bearing with LM104911 race, and the Timken 475960 hub seal. The spindle hardware is a Spicer 33732 six-point nut and 33733 washer, and the axle-end parts are the Spicer 700014 spindle needle bearing, 44506 thrust washer and seal combo, and 50381 boot seal.

Before you order

• Confirm the truck is a 2005-2014 Ford F-250 or F-350 Super Duty 4x4 and that your model year falls inside that range.
• While the knuckles are apart, it is a sensible time to replace the axle u-joints and ball joints. One owner-written install by two people, ball joints included, took just under nine hours.
• Dynatrac backs the kit with a one-year, unlimited-mileage written warranty.
• If anything about your truck's year, axle, or wheels is unclear, contact Skinny Pedal Racing with your model year and cab and chassis type before ordering.

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov