{"product_id":"currie-extreme-60-jeep-gladiator-axle-assemblies","title":"Currie Extreme 60 - Jeep Gladiator Axle Assemblies","description":"\u003cp\u003eThe Currie Extreme 60 1-ton front and rear axle assemblies for the 2020 and newer Jeep Gladiator are engineered for severe off-road use with up to 42-inch tall tires and V8 horsepower. The reinforced Extreme 60 center castings feature thick walls and heavy webbing, providing ultimate gear strength and durability. The front axle incorporates complete 1-ton inner and outer steering assemblies, and the rear implements 40-spline axles and billet full-floating hubs to deliver ultimate reliability. If you seek out the most challenging routes and most formidable obstacles to conquer, the Extreme 60 axles are a natural choice.\u003c\/p\u003e\u003cbr\u003e\u003cp\u003eContinue the journey and view the full details and features below:\u003c\/p\u003e\u003cbr\u003e\u003ch4\u003eCurrie Extreme 60 Details:\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eAvailable in 70 or 72.5-Inch Axle Widths\u003c\/li\u003e\n\u003cli\u003eChoice of Front or Rear only, or Full Axle Set\u003c\/li\u003e\n\u003cli\u003eChoice of Selectable Locker and Gear Ratio\u003c\/li\u003e\n\u003c\/ul\u003e\u003cbr\u003e\u003ch4\u003eExclusive Extreme 60 Features:\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eFront High-Clearance Center Section with Rotated Cover with Low-Friction Skid Plate Improves Obstacle Slide-Over\u003c\/li\u003e\n\u003cli\u003eFront 1-Ton Inner C's and Outer Steering Knuckles with Currie F350 Unit Bearings are Baja Proven and Ultra4 Tested Tough\u003c\/li\u003e\n\u003cli\u003eFront Heat-Treated Chromoly Tie Rod with 1-Ton Ends\u003c\/li\u003e\n\u003cli\u003eRear Heat-Treated Chromoly Full-Float Spindles, Billet Hubs, and 40-Spline Axles Deliver Maximum Strength and Durability\u003c\/li\u003e\n\u003cli\u003eMassive 14.250 in. Front and 13.75 in. Rear Vented Rotors Deliver Abundant Stopping Power\u003c\/li\u003e\n\u003cli\u003e8-Lug Wheel Bolt Pattern for Ultimate Reliability\u003c\/li\u003e\n\u003cli\u003eUV Stable Satin Black Powder Coat Finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003cbr\u003e\u003cp\u003eThe Extreme 60 axles for the 2020 and newer Jeep Gladiator JT are complete bolt-in axle assemblies with all required brackets and mounts in place. The vehicle's factory driveshafts will require modification or replacement to accommodate the larger 1350-series U-joint and 60-series housing. New 8-Lug wheels are required.\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eExtreme 60 Front Axle:\u003c\/strong\u003e\u003c\/h3\u003e\u003cstrong\u003eExtreme 60 High-Pinion\u003c\/strong\u003e\u003cp\u003eDesigned and optimized using computer simulation, the Extreme 60 is reinforced in critical areas with thicker walls and heavier webbing to deliver maximum strength, durability, and rigidity\u003c\/p\u003e\u003cstrong\u003eRadius Center Section\u003c\/strong\u003e\u003cp\u003eThe radius bottom center section with replaceable AR400 skid plate delivers unmatched ground clearance and improved obstacle slide-over\u003c\/p\u003e\u003cstrong\u003eAxle Tubes\u003c\/strong\u003e\u003cp\u003eLarge 3.5 in. diameter x .375 wall axle tubes (left) are more than two times stronger than the stock axle tubes (right) without being overweight or sacrificing ground clearance\u003c\/p\u003e\u003cstrong\u003ePinion Oiling\u003c\/strong\u003e\u003cp\u003eHigh volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminating oil starvation issues\u003c\/p\u003e\u003cstrong\u003eSteering Geometry\u003c\/strong\u003e\u003cp\u003eFront axle steering geometry is optimized for large tires and lifted vehicles with increased caster and pinion angles\u003c\/p\u003e\u003cstrong\u003ePinion Yoke\u003c\/strong\u003e\u003cp\u003eThe upgraded 1350 pinion yoke provides increased strength and reliability over the failure-prone factory CV joint\u003c\/p\u003e\u003cstrong\u003eChromoly Tie Rod \u003c\/strong\u003e\u003cp\u003eThe included heavy-duty tie rod features a 1.375 OD x .375 wall heat-treated chromoly tube, and 1-ton forged rod ends that are designed to withstand off-road abuse and large tires\u003c\/p\u003e\u003cstrong\u003eForged Inner Knuckles\u003c\/strong\u003e\u003cp\u003eMassive forged 1-ton inner knuckles (right) are designed to stand up to severe off-road punishment and large tires without flinching\u003c\/p\u003e\u003cstrong\u003e1-Ton Steering Assemblies\u003c\/strong\u003e\u003cp\u003eComplete 1-ton outer steering assemblies deliver massive strength, while 14.25-inch diameter vented rotors and Jeep Gladiator dual-piston calipers provide the increased brake capacity required for stopping big tires\u003c\/p\u003e\u003cstrong\u003ePremium Hubs\u003c\/strong\u003e\u003cp\u003eWarn® premium manual locking hubs are the industry standard for durability and reliability\u003c\/p\u003e\u003cstrong\u003eDifferential Cover\u003c\/strong\u003e\u003cp\u003eRock-proof Currie nodular iron front cover protects expensive internals, adds structural support to the housing's face flange, and locates the driver’s side upper control arm mount\u003c\/p\u003e\u003cstrong\u003eControl Arm Mounts\u003c\/strong\u003e\u003cp\u003eLower control arm mounts are one-piece construction with integrated skid plates to help fend off bracket-seeking rocks\u003c\/p\u003e\u003cstrong\u003ePowder Coat Finish\u003c\/strong\u003e\u003cp\u003eUV Stable Satin black powder coat finish adds long-lasting protection against rust and corrosion to keep your Extreme 60 looking its best\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eExtreme 60 Rear Axle:\u003c\/strong\u003e\u003c\/h3\u003e\u003cstrong\u003eCurrie Extreme 60\u003c\/strong\u003e\u003cp\u003eDesigned and optimized using computer simulation, the Extreme 60 is reinforced in critical areas with thicker walls and heavier webbing to deliver maximum strength, durability, and rigidity\u003c\/p\u003e\u003cstrong\u003e60-Series Gear\u003c\/strong\u003e\u003cp\u003eGear diameter equals strength - the Extreme 60's 9.75\" gear (right) provides greater torque and load handling capacity when compared to the stock 8.66\" gear (left)\u003c\/p\u003e\u003cstrong\u003eAxle Tubes\u003c\/strong\u003e\u003cp\u003eLarge 3.5 in. diameter .375 wall axle tubes (left) are more than 3x the strength of the stock tubes (right) without being overweight or sacrificing ground clearance\u003c\/p\u003e\u003cstrong\u003eChromoly Axles\u003c\/strong\u003e\u003cp\u003eCurrie 40-spline full-floating chromoly axles are the largest in the industry and provide 1.5x the strength of 35-spline chromoly axles\u003c\/p\u003e\u003cstrong\u003eFull-Float Hubs\u003c\/strong\u003e\u003cp\u003eDesert race-inspired heat-treated Chromoly spindles with billet steel full-floating hubs carry the vehicle's weight, eliminating the influence of side loading and impact shock on axle durability. Modified OEM backing plates and parking brake assemblies provide reliable operation with broad availability of serviceable wear items\u003c\/p\u003e\u003cstrong\u003eBig Brakes\u003c\/strong\u003e\u003cp\u003e13.750-inch vented rotors and OE Jeep Gladiator calipers provide the stopping power with factory pedal feel, while the 8-lug bolt pattern improves reliably with large, heavy tires\u003c\/p\u003e\u003cstrong\u003ePinion Yoke\u003c\/strong\u003e\u003cp\u003eThe upgraded 1350 pinion yoke provides increased strength and reliability over the failure-prone factory CV Joint\u003c\/p\u003e\u003cstrong\u003eLaser Cut Brackets\u003c\/strong\u003e\u003cp\u003eCurrie heavy-duty laser cut brackets provide increased strength and maintain compatibility with stock and aftermarket suspension components\u003c\/p\u003e\u003cstrong\u003eIron Cover\u003c\/strong\u003e\u003cp\u003eCurrie rock-proof nodular iron cover protects expensive internals and adds structural support to the housing's face flange\u003c\/p\u003e\u003cstrong\u003ePowder Coat Finish\u003c\/strong\u003e\u003cp\u003eUV Stable Satin black powder coat finish adds long-lasting protection against rust and corrosion to keep your Extreme 60 looking its best\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNotes\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eABS Sensors\u003c\/strong\u003e - Axles do not include ABS sensors; the factory sensors from the stock axles must be retained and installed on the Extreme 60 front and rear axle assemblies\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eComputer Programming: \u003c\/strong\u003eA programmer is required to reset the gear ratio and tire height settings in the vehicle's computer for the proper function of the vehicle's stability control and transmission shift points when larger than stock tires are installed\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBrake System:\u003c\/strong\u003e The big brake kit included with the Extreme 60 uses 14.250-inch rotors and Jeep Gladiator dual-piston calipers in the front and 13.75-inch vented rotors and Gladiator calipers in the rear\u003cbr\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWheel and Tire Size:\u003c\/strong\u003e For proper brake caliper clearance, 17-inch or larger wheels are required. Wheels must have a 4.9-inch (125 mm) hub bore with a recommended 4.5-inch backspace. The maximum recommended tire size is 42 inches\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eOverall Width:\u003c\/strong\u003e Axles are available in 70- or 72.5-inch widths between wheel mounting surfaces. This additional width improves the frame and body clearance for large tires and provides additional space for coil-over shocks.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSteering Stabilizer:\u003c\/strong\u003e The Extreme 60 ram assist bracket requires an aftermarket stud-style track bar bolt to accommodate a steering stabilizer. Trac bar bolts are available from FOX Racing P\/N 803-02-028 or Synergy Manufacturing P\/N 8806-01\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eVehicle Fitment: 2020 and Newer Jeep Gladiator Truck\u003c\/li\u003e\n\u003cli\u003eExtreme 60: ___________________________________________________________________________________\u003c\/li\u003e\n\u003cli\u003ePinion Yoke: 1350 series u-joint\u003c\/li\u003e\n\u003cli\u003eDifferential Cover: Currie nodular-iron cover, Red\u003c\/li\u003e\n\u003cli\u003eAxle Tubes: 3.5 inch diameter, .375 wall DOM tube\u003c\/li\u003e\n\u003cli\u003eSuspension Brackets: Heavy gauge 3\/16 steel mounting brackets\u003c\/li\u003e\n\u003cli\u003eWidth: 70 or 72.5-inches wide (between wheel mounting surfaces)\u003c\/li\u003e\n\u003cli\u003eWheel Bolt Pattern: 8-lug (8 x 6.5 in.) with 9\/16-18 studs\u003c\/li\u003e\n\u003cli\u003eFinish: UV stable satin black powder coat\u003c\/li\u003e\n\u003cli\u003eFront Extreme 60: ___________________________________________________________________________________\u003c\/li\u003e\n\u003cli\u003eCenter Section: Extreme 60 nodular iron high-clearance center section with rotated cover, and replaceable hardened steel skid plate\u003c\/li\u003e\n\u003cli\u003ePinion Oiling: High volume flow-thru recirculating oil system\u003c\/li\u003e\n\u003cli\u003eGear Set: 60 series reverse rotation thick gear sets\u003c\/li\u003e\n\u003cli\u003eSkid Plate: AR400 hardened steel skid plate\u003c\/li\u003e\n\u003cli\u003eAxles: Currie Extreme 35-spline (1.5 in. diameter) 4340 Chromoly inner and outer axle shafts with 1480 u-joints\u003c\/li\u003e\n\u003cli\u003eEnd Forgings: Currie 1-ton heavy-duty forged steel inner C’s\u003c\/li\u003e\n\u003cli\u003eSteering Knuckles: Currie 1-ton nodular iron steering knuckles machined and keyed for high-steer arms\u003c\/li\u003e\n\u003cli\u003eUnit Bearings: 1-ton unit bearings with JK tone rings installed for ABS and ESP retention\u003c\/li\u003e\n\u003cli\u003eHubs: Warn Premium locking 35-spline hubs\u003c\/li\u003e\n\u003cli\u003eBrake Rotors: 14.250-inch vented rotors (over 1.25 in. larger diameter than stock, provides increased brake force)\u003c\/li\u003e\n\u003cli\u003eBrake Calipers: Jeep Gladiator dual-piston front calipers\u003c\/li\u003e\n\u003cli\u003eTie Rod: 1-ton 1.375 in. OD x .375 wall heat treated chromoly tube with forged tie rod ends\u003c\/li\u003e\n\u003cli\u003eGeometry: Optimized for stock height or lifted vehicles with 5 degrees of pinion angle and 5 degrees of caster angle\u003c\/li\u003e\n\u003cli\u003eTrack Bar \/ Stabilizer Mount: Integrated raised track bar and ram-assist mount setup for PSC 8-inch travel ram\u003c\/li\u003e\n\u003cli\u003eOil Capacity: 2.5 quarts of 75W-140 synthetic gear oil (API GL-5 Rated), 3.0 quarts of 75W-140 synthetic gear oil (API GL-5 Rated)\u003c\/li\u003e\n\u003cli\u003eRear Extreme 60: ___________________________________________________________________________________\u003c\/li\u003e\n\u003cli\u003eRear Center Section: Extreme 60 standard rotation nodular iron center section with thick webbing and reinforcement in critical areas\u003c\/li\u003e\n\u003cli\u003eRear Axle: Currie Extreme double splined full-floating 40-spline (1.7-inch diameter) 4340 heat-treated chromoly\u003c\/li\u003e\n\u003cli\u003eFloater Spindle: Currie Full-float 2.5-inch heat-treated 4140 Chromoly spindles\u003c\/li\u003e\n\u003cli\u003eFloater Hub: Currie billet steel full-floating hubs with 40-spline drive flanges, JT tone rings installed\u003c\/li\u003e\n\u003cli\u003eRear Rotors: 13.750-inch vented rotors\u003c\/li\u003e\n\u003cli\u003eRear Brake Calipers: Jeep Gladiator truck rear calipers\u003c\/li\u003e\n\u003cli\u003eParking Brake: Modified for floater OEM backing plate and parking brake assembly\u003c\/li\u003e\n\u003cli\u003eRear Geometry: Optimized for stock height and lifted vehicles with 5 degrees of pinion angle\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuild options\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eStart Your Build: Rear Axle Only, Front Axle Only, Front and Rear Set\u003c\/li\u003e\n\u003cli\u003eSelect Axle Width: 70-Inch Axle Width, 72.5-Inch Axle Width (+2 weeks)\u003c\/li\u003e\n\u003cli\u003eSelect Diff Cover Color: Red Powder Coat, Black Powder Coat\u003c\/li\u003e\n\u003cli\u003eSelect Ratio: 4.56 Gears, 4.88 Gears, 5.13 Gears, 5.38 Gears\u003c\/li\u003e\n\u003cli\u003eSelect Locker: ARB Air Locker, Eaton ELocker\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eProduct information\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePart numbers vary by build options\u003c\/li\u003e\n\u003cli\u003eBrand: Currie Enterprises\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Currie Enterprises","offers":[{"title":"Default Title","offer_id":45919757402178,"sku":null,"price":8800.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1476\/5984\/files\/0018655_currie-extreme-60-jeep-gladiator-axle-assemblies.jpg?v=1794112995","url":"https:\/\/www.skinnypedalracing.com\/products\/currie-extreme-60-jeep-gladiator-axle-assemblies","provider":"Skinny Pedal Racing","version":"1.0","type":"link"}