{"product_id":"currie-60-jeep-tj-lj-jk-hybrid-rear-axle-assembly","title":"Currie 60 - Jeep TJ\/LJ - JK Hybrid Rear Axle Assembly","description":"\u003cp\u003eCurrie HD60 Hybrid axle assembly for the 1997-2006 Jeep TJ\/LJ incorporates the unmatched strength of the Currie HD60 casting with an additional 5 inches of width, JK housing ends, and TJ bracketry. The high-pinion design and exclusive rotated center section of the HD60 provide superior driveshaft clearance and obstacle slide-over for enhanced performance. If you enjoy tackling challenging routes and formidable obstacles, the Currie HD60 axle is ideal.\u003c\/p\u003e\u003cbr\u003e\u003ch4\u003eDetails:\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eComplete Currie HD60 High-Pinion Rear Axle \u003c\/li\u003e\n\u003cli\u003eCurrie TJ Brackets Installed\u003c\/li\u003e\n\u003cli\u003eJK 65.375 in. Width (+4.9 in.)\u003c\/li\u003e\n\u003cli\u003eJK 5 x 5 Wheel Bolt Pattern\u003c\/li\u003e\n\u003cli\u003eHigh-Pinion Design Raises the Driveshaft by 2-Inches to\u003cp\u003eReduces Driveline Angle and Improves Clearance\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003eRock Slider Low-Friction Skid Plate Sides Over Trail Obstacles with Ease\u003c\/li\u003e\n\u003cli\u003eCurrie 35-spline Semi-Float Axles\u003c\/li\u003e\n\u003cli\u003e3 in. Diameter x .5 in. Wall DOM Axle Tubes\u003c\/li\u003e\n\u003cli\u003eChoice of Gear Ratio, Axle Spline and Locker\u003c\/li\u003e\n\u003cli\u003eSatin Black Powder Coat Finish For Long Lasting Protection\u003c\/li\u003e\n\u003cli\u003eRequires Additional Components - See Notes Below\u003c\/li\u003e\n\u003c\/ul\u003e\u003cbr\u003e\u003cp\u003eThe HD60 high-pinion axle for the Jeep Wrangler TJ is a complete bolt-in axle assembly with all required brackets and mounts in place. The vehicle's factory driveshaft will require modification or replacement to accommodate the larger 60-series housing and 1350 series u-joint.\u003c\/p\u003e\u003ch3\u003e\u003cstrong\u003eProduct Features:\u003c\/strong\u003e\u003c\/h3\u003e\u003cstrong\u003eCurrie HD60 High-Pinion\u003c\/strong\u003e\u003cp\u003eDesigned and optimized using computer simulation, the HD60 is reinforced in critical areas with thicker walls and heavier webbing to deliver maximum strength, durability, and rigidity\u003c\/p\u003e\u003cstrong\u003eRock Slider\u003c\/strong\u003e\u003cp\u003eIntegrated AR400 hardened steel skid plate resists deformation and gouging to slide over obstacles far better than iron housings or mild steel plates\u003c\/p\u003e\u003cstrong\u003eAxle Tubes\u003c\/strong\u003e\u003cp\u003e3-inch diameter x .375 wall tubes are greater than 2x the strength of the factory 35\/44 2.5 diameter x .250 axle tubes\u003c\/p\u003e\u003cstrong\u003eLarger Pinion Bearing\u003c\/strong\u003e\u003cp\u003eLarge diameter outer pinion bearing (right) is designed for the demands of reverse rotation\/high pinion housings. Stock low pinion bearing (left)\u003c\/p\u003e\u003cstrong\u003ePinion Oiling\u003c\/strong\u003e\u003cp\u003eHigh volume flow-thru recirculating oil system keeps pinion bearings bathed in cool oil, reducing operating temperatures and eliminating oil starvation issues\u003c\/p\u003e\u003cstrong\u003eTJ Brackets\u003c\/strong\u003e\u003cp\u003eCurrie heavy-duty TJ brackets provide increased strength and maintain compatibility with stock and aftermarket suspension components\u003c\/p\u003e\u003cstrong\u003eJK Housing Ends\u003c\/strong\u003e\u003cp\u003eJK Set80 housing end with 5 x 5 wheel bolt pattern accepts standard or aftermarket JK brake components for a significantly increased stopping power over factory TJ brakes\u003c\/p\u003e\u003cstrong\u003ePinion Yoke\u003c\/strong\u003e\u003cp\u003eThe upgraded 1350 pinion yoke provides increased strength and reliability over the factory 1310 yoke\u003c\/p\u003e\u003cstrong\u003eIron Cover\u003c\/strong\u003e\u003cp\u003eRock-proof Currie nodular iron cover protects expensive internals and adds structural support to the housing's face flange for increased rigidity\u003c\/p\u003e\u003cstrong\u003ePowder Coat Finish\u003c\/strong\u003e\u003cp\u003eUV Stable Satin black powder coat finish adds long-lasting protection against rust and corrosion to keep your Currie 60 looking its best\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNotes:\u003c\/strong\u003e\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDriveshaft: \u003c\/strong\u003eThe driveshaft will require modification or replacement to accommodate the larger 60-series housing and 1350 series u-joint\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eBrakes: \u003c\/strong\u003eCompatible with stock JK or aftermarket JK-compatible brake assemblies (Not included)\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eSway Bar:\u003c\/strong\u003e Requires the use of an aftermarket sway bar such as the RockJock Antirock or equivalent (Not included)\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWheel Bolt Pattern: \u003c\/strong\u003eThe WBP is JK 5 x 5\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eVehicle Fitment: 1997 thru 2006 Wrangler TJ\/LJ\u003c\/li\u003e\n\u003cli\u003eCenter Section: Currie 60 nodular Iron high-pinion radius bottom center section with thicker walls and webbing\u003c\/li\u003e\n\u003cli\u003ePinion Bearing: Large diameter front pinion bearing matched to rear bearing\u003c\/li\u003e\n\u003cli\u003ePinion Oiling: High volume flow-thru recirculating oil system\u003c\/li\u003e\n\u003cli\u003eGear Set: Standard Dana 60™, compatible with super 60 reverse cut gears\u003c\/li\u003e\n\u003cli\u003ePinion Yoke: 1350 u-joint\u003c\/li\u003e\n\u003cli\u003eSkid Plate: AR400 hardened steel skid plate\u003c\/li\u003e\n\u003cli\u003eDifferential Cover: Currie nodular-iron cover with gasketed fill plug with dipstick, Red\u003c\/li\u003e\n\u003cli\u003eAxle Tubes: 3 in. diameter, .5 wall DOM tube\u003c\/li\u003e\n\u003cli\u003eAxle Bearings: Set 20 tapered roller bearing\u003c\/li\u003e\n\u003cli\u003eAxles: Currie Performance semi-floating, 35-spline (1.5” diameter) 4340 chromoly axles\u003c\/li\u003e\n\u003cli\u003eSuspension Brackets: Heavy gauge 3\/16” steel mounting brackets with multiple mounting locations that enable the suspension geometry to be tuned\u003c\/li\u003e\n\u003cli\u003eGeometry: Optimized for 4” lift kits with 5 degrees of pinion angle to reduce driveshaft angle and 5 degrees of caster for improved steering\u003c\/li\u003e\n\u003cli\u003eWheel Bolt Pattern: 5 x 5 single pattern, .5-inch press-in studs\u003c\/li\u003e\n\u003cli\u003eWidth: 60.50 inch wide (stock TJ width)\u003c\/li\u003e\n\u003cli\u003eFinish: Black satin powder coat\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eBuild options\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eSelect Diff Cover Color: Red Powder Coat, Black Powder Coat\u003c\/li\u003e\n\u003cli\u003eSelect Gear Ratio: 4.56 Gears, 4.88 Gears, 5.13 Gears, 5.38 Gears\u003c\/li\u003e\n\u003cli\u003eSelect Locker: Detroit Truetrac, ARB Air Locker, Electric Locker\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eProduct information\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePart numbers vary by build options\u003c\/li\u003e\n\u003cli\u003eBrand: Currie Enterprises\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Currie Enterprises","offers":[{"title":"Default Title","offer_id":45919756156994,"sku":null,"price":5750.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1476\/5984\/files\/0018691_currie-60-jeep-tjlj-jk-hybrid-rear-axle-assembly.jpg?v=1794112857","url":"https:\/\/www.skinnypedalracing.com\/products\/currie-60-jeep-tj-lj-jk-hybrid-rear-axle-assembly","provider":"Skinny Pedal Racing","version":"1.0","type":"link"}