{"title":"Motobilt Ford 10.25 \/ 10.5 Differential Cover","description":"\u003cp\u003eMotobilt Ford 10.25 \/ 10.5 differential covers.\u003c\/p\u003e","products":[{"product_id":"motobilt-sterling-10-25-or-10-5-differential-cover-integrated-3-4-npt-fill-plug-mb4032","title":"Motobilt Sterling 10.25 or 10.5 Differential Cover Integrated 3\/4\" NPT Fill Plug MB4032","description":"\u003cp\u003e\u003cstrong\u003eMotobilt Sterling 10.25 or 10.5 Differential Cover Integrated 3\/4\" NPT Fill Plug MB4032\u003c\/strong\u003e – Motobilt part number \u003cstrong\u003eMB4032\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eThe Motobilt Ford Sterling 10.25 \/10.5 HD steel diff cover has many features that separate it from others. The Sterling 10.25\/10.5 HD steel diff cover features a 3\/8 inch thick steel ring that will keep the cover from pulling away from the housing when dragging over rocks. The Sterling 10.25 \/10.5 HD steel diff cover also features the proven 1\/4 inch thick steel plate design with an integrated 3\/4 inch NPT fill plug. The fill plug on the Sterling 10.25 \/ 10.5 HD steel diff cover allows for easy access, especially when a truss system is commonly used.\u003c\/p\u003e\n\u003cp\u003eThe Sterling 10.25\/10.5 HD steel diff cover is welded both on the inside and outside of the cover to ensure maximum penetration for superior strength. The Sterling 10.25\/10.5 HD steel diff cover's design comes from over 14 years of diff cover testing and manufacturing experience. The diff cover ships bare steel and will need to be painted. We do not usually powdercoat ours because the diff cover is going to take abuse from rocks. Spray paint works well so you can simply touch it up. The bolts and fill plug ship with the cover.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSterling 10.25 and 10.5 diff cover\u003c\/li\u003e\n\u003cli\u003e3\/8 inch thick steel ring\u003c\/li\u003e\n\u003cli\u003e1\/4 inch thick steel plate\u003c\/li\u003e\n\u003cli\u003eIntegrated 3\/4 inch NPT fill plug\u003c\/li\u003e\n\u003cli\u003eLifetime Warranty\u003c\/li\u003e\n\u003cli\u003eSold as each\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShips bare steel and will need to be painted\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMaterial: Steel\u003c\/li\u003e\n\u003cli\u003eFinish: Bare steel\u003c\/li\u003e\n\u003cli\u003eThickness: 1\/4 Inch\u003c\/li\u003e\n\u003cli\u003eLocation: Rear\u003c\/li\u003e\n\u003cli\u003eDifferential: Ford 10.5 Inch\u003c\/li\u003e\n\u003cli\u003eSold as: Each\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eProduct information\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMotobilt part number: MB4032\u003c\/li\u003e\n\u003cli\u003eCountry of origin: USA\u003c\/li\u003e\n\u003cli\u003ePackage size: 14 x 14 x 6 in\u003c\/li\u003e\n\u003cli\u003eShipping weight: 15 lb\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eResources\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\u003cli\u003e\u003ca href=\"https:\/\/youtu.be\/6ld0nbbA_TE\" target=\"_blank\" rel=\"noopener\"\u003eProduct video\u003c\/a\u003e\u003c\/li\u003e\u003c\/ul\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":45374403674178,"sku":"MB4032","price":149.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1476\/5984\/files\/MB4032-HJQL.jpg?v=1791253331"},{"product_id":"motobilt-diy-sterling-10-25-10-5-diff-cover-mb4032-diy","title":"Motobilt DIY Sterling 10.25 \/10.5 Diff Cover MB4032-DIY","description":"\u003cp\u003e\u003cstrong\u003eMotobilt DIY Sterling 10.25 \/10.5 Diff Cover MB4032-DIY\u003c\/strong\u003e – Motobilt part number \u003cstrong\u003eMB4032-DIY\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIf you can weld and want to build your own diff cover, purchase the Sterling 10.25 \/10.5 DIY DIFF Cover. Motobilt DIY Diff Covers are the same as our fully-welded diff covers, but sold as a kit including the pre-formed pieces and hardware you will need to complete the DIY project yourself. We have included assembly instructions as well.\u003c\/p\u003e\n\u003cp\u003eWhy change out your diff cover? We do get asked this question on occasion. The factory diff covers are too thin for abuse on the trail. One of the common factory diff cover failures occurs when the edge gets peeled up from a rock sliding across the diff. Peeling can cause the differential fluid to leak out unknowingly and the result could be damaging the gears when you hit the road to drive home.\u003c\/p\u003e\n\u003cp\u003eAnother failure of factory diff covers are from bending the cover into the ring gear which rubs a hole through. The result here is the same with differential fluid leaking out. One other failure is actually puncturing the factory diff cover with a sharp rock. Again resulting in differential fluid leaking out.\u003c\/p\u003e\n\u003cp\u003eHopefully this explains the need for a heavy duty diff cover. The Motobilt Heavy Duty Fabricated Diff Covers address the failures I have mentioned to ensure your ring and pinion gear sets are well protected.\u003c\/p\u003e\n\u003cp\u003eAll Motobilt Diff Covers include a Lifetime Warranty from trail damage and manufacture defect. We cannot warranty DIY Diff Covers being welded incorrectly.\u003cbr\u003eAs with all Motobilt DIY builder parts, an experienced welder is recommended.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation Note: \u003c\/strong\u003eWe strongly recommend tacking the pieces together and test fitting it onto the axle before finish welding. We also recommend using pipe thread tape for the fill plug.\u003cbr\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDIY Diff Cover Kit Features:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e1\/4 inch thick steel plate shell\u003c\/li\u003e\n\u003cli\u003e3\/8 inch thick steel diff ring\u003c\/li\u003e\n\u003cli\u003eIn-house laser and CNC press brake\u003c\/li\u003e\n\u003cli\u003eSold as kit\u003c\/li\u003e\n\u003cli\u003eAll parts are shipped bare metal and will need to be painted before install\u003c\/li\u003e\n\u003cli\u003eLifetime Warranty\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eDIY Diff Cover Kit includes:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLaser-cut 3\/8 inch Ring\u003c\/li\u003e\n\u003cli\u003eCNC-formed 1\/4 inch thick shell\u003c\/li\u003e\n\u003cli\u003eOil fill weld-in bung and oil fill plug\u003c\/li\u003e\n\u003cli\u003eMounting hardware\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eSpecifications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMaterial: Steel\u003c\/li\u003e\n\u003cli\u003eFinish: Bare steel\u003c\/li\u003e\n\u003cli\u003eDifferential: Sterling 10.25\/10.5\u003c\/li\u003e\n\u003cli\u003eHardware included: Yes\u003c\/li\u003e\n\u003cli\u003eSold as: Kit\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eProduct information\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMotobilt part number: MB4032-DIY\u003c\/li\u003e\n\u003cli\u003eCountry of origin: USA\u003c\/li\u003e\n\u003cli\u003ePackage size: 12 x 12 x 6 in\u003c\/li\u003e\n\u003cli\u003eShipping weight: 5 lb\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eCalifornia Proposition 65 warning:\u003c\/strong\u003e Cancer and Reproductive Harm – \u003ca href=\"https:\/\/www.P65Warnings.ca.gov\" target=\"_blank\" rel=\"noopener\"\u003ewww.P65Warnings.ca.gov\u003c\/a\u003e\u003c\/p\u003e","brand":"Motobilt","offers":[{"title":"Default Title","offer_id":45375064768578,"sku":"MB4032-DIY","price":140.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1476\/5984\/files\/MB4032-DIY-HJQL.jpg?v=1791254030"}],"url":"https:\/\/www.skinnypedalracing.com\/collections\/motobilt-ford-10-25-10-5-differential-cover.oembed","provider":"Skinny Pedal Racing","version":"1.0","type":"link"}